Heart Ashtray Mold, Ashtray Silicone Mold, Heart Molds, Resin Molds fo - Zapp3D Design LLC
4.8 (771) · $ 17.00 · In stock
This listing is for a Heart Ashtray Mold. The size of this ashtray is approximately 4.5" tall, 5" wide, and it's 1" deep. The final product comes out completely shiny. Please message us with any questions you may have regarding this mold. **Please note this listing is for the silicone mold ONLY. All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal) Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable
This listing is for a Heart Ashtray Mold. The size of this ashtray is approximately 4.5" tall, 5" wide, and it's 1" deep. The final product comes out completely shiny. Please message us with any questions you may have regarding this mold. **Please note this listing is for the silicone mold ONLY. All molds are handmade and inspected before shipping. All trays are made from stacked acrylic which may cause a line to appear in the mold. (Very minimal) Our Smoothon Mold Star silicone molds cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Our molds will last a long time in your mold library and are good for resin, concrete, wax, gypsum and other materials. The molds are heat resistant up to 450 degrees Fahrenheit or 232 degrees Centigrade. They are suitable for casting low temperature melt metal alloys. SILICONE MOLD CARE INSTRUCTIONS • DON’T TOUCH the inside shiny part of the mold. This will cause permanent scuffs that will show in your final cast. • Use scotch tape to gently clean the mold. Tap the spot lightly where there are loose particles. • USE EXTREME CAUTION when using a torch/heat gun to pop bubbles in the resin. It may rip the mold upon demolding your fully cured resin. Instead try a mist of alcohol over the resin. • Make sure the resin is fully. Uncured resin may rip the mold. • Please follow all safety precautions when using resin. It is very toxic. • Plastic Wrap/Bag Marks on trays will go away within 48-72 hours. • All torso molds come pre-split to allow for easy demolding of your resin piece. Use the rubber bands to aid you to seal the split upon pouring. • If you have further questions or concerns about your mold, please shoot me a message on and I’ll get you taken care of. PLEASE INSPECT MOLD PRIOR TO FIRST USE. I DO NOT ACCEPT RETURNS OF USED MOLDS.
FanFlex: Lightweight flexible crests and patches that fold easy. - FanTex: An all-new super comfortable soft fabric. - FanFit: The authentic on-ice
Coffin Ashtray Mold, Coffin Mold, Ashtray Silicone Mold, Resin Molds Ashtrays, Ash Tray Mold, Coffin Tray Mold
Deep Rainbow Mold, 2 Sizes, ULTRA Quality
Heart FLAT Molds, 3 Sizes
Round Ashtray Mold for Resin, Circle Ashtray Mold, Ashtray Mold, Ash T - Zapp3D Design LLC
Valentine's Day - Zapp3D Design LLC
Palette Mold, 4 Sizes
Valentine's Day - Zapp3D Design LLC
Silicone Mold Ashtray Resin Mold Heart Square Mold For DIY Resin UV Crystal Epoxy Crafts Crystal Ashtray Home Decoration
Heart Dish Silicone Mold for Resin, Jewelry Holder, Ring Dish, Silicon - Zapp3D Design LLC
Ashtray Mold
Square Ashtray Mold, Ashtray Silicone Mold, Resin Molds for Ashtray, A - Zapp3D Design LLC